Particle lifts years of baked-on grease, oil, and Alberta road salt out of your engine bay with dry ice — no water, no chemicals, and no risk to wiring, sensors, or paint. It leaves an engine looking factory-fresh. Based in Sherwood Park, we’re mobile across Edmonton and area — we come to you.
Serving drivers, restorers, and shops across Edmonton and Sherwood Park — if it has an engine and years of grime, dry ice will lift it, without the water, grit, or chemicals that traditional cleaning forces into your driveway and your wiring.
Years of oil mist, grease, and dust bake onto an engine and never come off with a rag. Dry ice flash-freezes it and lifts it away — down to clean metal, painted valve covers, and legible casting marks — with no water near your electronics and no chemical residue left behind. The single best way to make an engine bay look factory-fresh.
Decades of grime lifted from engines, frames, and undersides without sanding, soaking, or stripping original paint, plating, and decals. The restorer’s way to get back to bare material without losing what makes the car original.
Alberta winters cake frames and underbodies in road salt and grease that eat metal from below. Dry ice strips it off without abrasion so you can inspect, treat, or re-undercoat clean steel — and slow the rust.
Mud, chain lube, and burnt-on grime blasted off dirt bikes, quads, sleds, and small engines — without water in the electronics or media that lodges in the fins and seals. Race-clean before the next ride.
This is what dry ice does to baked-on grease and grime — no scrubbing, no soaking, no abrasion. The satisfying part is watching it happen.
Before
After
Pressure washers force water into connectors and fuses. Degreasers leave residue and run into the storm drain. Sandblasting eats paint and plating. Dry ice does none of that.
Nothing to short out your electronics and nothing running into your driveway or the storm drain — just clean, dry results.
CO2 is non-conductive, so we clean right around wiring, sensors, and connectors without soaking or shorting anything.
It lifts grime without touching the surface underneath — paint, plating, decals, and gaskets stay intact.
No harsh degreasers and no residue left on the engine — frozen CO2 turns to gas and disappears.
Reaches into seams, fins, and tight spots a cloth or brush will never touch, and lifts grime that’s been baked on for years.
We come to your shop, garage, or acreage — fully insured and WCB covered, across the Edmonton area.
Frozen CO2 pellets hit the grime at high speed — and physics does the rest.
Pellets at −78.5°C flash-freeze the grease and grime, cracking its bond with the metal underneath.
The frozen layer becomes brittle and lets go of the surface — without any abrasion to the material below.
The CO2 turns straight from solid to gas, so there’s no media, no water, and no residue — only the loosened dirt to sweep up.
Every vehicle is different, so we price per job after a quick look — but here’s the honest range so you know what to expect. Send a couple of photos and we’ll give you a flat price before we start.
A standard engine bay with typical buildup — the most-requested job, and the one that makes the biggest visual difference.
Decades of grime, original finishes to protect, and more careful masking — priced by the engine, frame, or full build.
Dirt bikes, quads, sleds, small engines, and truck undercarriages — priced by size and how heavy the buildup is.
Prefer a firm number first? Text a couple of photos to 780.394.4123 and we’ll quote you a flat price — no surprises on the day.
Based in Sherwood Park and coming to shops, garages, and acreages across Edmonton and the surrounding communities.
Particle provides waterless dry ice engine bay cleaning and automotive detailing across the Edmonton area. Unlike a pressure wash or degreaser, dry ice blasting removes baked-on grease, oil, and road salt without forcing water into wiring, sensors, or fuses — and without leaving chemical residue behind. It’s non-abrasive, so original paint, plating, decals, and gaskets come through untouched.
From daily drivers and trucks to classic and collector cars, frame-off restorations, dirt bikes, and truck undercarriages, it’s the safest and most thorough way to get an engine or frame back to clean metal.
We’re a mobile service — we bring the equipment to your shop, garage, or acreage anywhere in Sherwood Park, Edmonton, St. Albert, Fort Saskatchewan, Leduc, Spruce Grove, Beaumont, and Stony Plain. Fully insured and WCB covered.
Getting a car ready to sell, prepping a build for paint, or just want your engine bay to look the way it did off the line? Get a quote or call 780.394.4123.
The questions we get most from car owners, restorers, and shops.
Tell us about your vehicle — a couple of photos of the engine bay help us quote a flat price. Prefer to talk? Call or text anytime.
Call or Text